Supported technology/Weather Station
tahmo.org/weather-stations-and-climate-data
| Direction | Data provider |
| Data | Sensor readings (stationary subjects) |
| Platform | Gundi v2 |
| Type | Pull integration |
TAHMO sends weather station readings to EarthRanger through Gundi. Gundi checks your TAHMO account on a schedule, and each station shows up as a stationary subject with its readings.
What you'll receive
We add details here as we confirm what TAHMO sends. If you know something we're missing, let us know.
| Positions | Yes, one stationary subject per station on your TAHMO account, named with the station code and placed at the station's location from TAHMO. Stations TAHMO can't answer for are skipped for that check and noted in the Route's Activity Logs. |
| Alerts and events | No |
| Sensor readings | Every measurement the station reports, named as TAHMO describes it, such as temperature. Measurements TAHMO has no description for are left out. |
| Photos and files | No |
| Past data | Yes. The first time Gundi sees a station, it fetches the last 24 hours. After that, each check picks up from the last reading sent, going back at most 3 days. |
How this integration works
This is a pull integration. Gundi checks the data provider for new data on a schedule, using the account details you enter in the Route, and passes what it finds on to your destination.
Who's involved
- You create the Route in Gundi and enter your provider account details, or give them to Gundi support when the setup badge says so.
- The data provider keeps your account and devices active.
- Your destination, for example EarthRanger, is where the data shows up.
- Gundi support helps only when the setup badge at the top of this page says so.
Historical data
When you first connect, Gundi fetches a limited amount of past data. How far back it goes depends on the integration and is shown under "Past data" above.
When data doesn't show up
Check your Route Activity Logs first: wrong account details and provider outages show up there. Then check with the provider that your devices are reporting.
How often data arrives
Gundi checks on a schedule. Where we know how often, it's shown under "Data Pull Frequency" on this page. New data arrives after the next check, plus the time the device takes to upload it to the provider.
Prerequisites
Data Source
You will need:
- TAHMO username and password
Data Delivery
EarthRanger
To send event data to EarthRanger, you will need:
- A special EarthRanger user (e.g., “Gundi Service Account”) for this integration. Please refer to EarthRanger's documentation or contact Support.
- A long-lived token for authentication assigned to the user created in the previous step. Please refer to EarthRanger's documentation or contact Support.
Configuration in Gundi
Login to Gundi.
Click on Create Route.
Select TAHMO.
Configure your TAHMO credentials under Username and Password.
Select your Workspace.
Enter a name for this Route (e.g., “TAHMO - AccountName”)
Click Next.
Click Add destination on the flow map and select a destination. Please consult
our guide.
Next Steps
EarthRanger
The following configurations are optional:
1. Select the data you want to see in the map.
1.1. Log in to EarthRanger as an admin (site.pamdas.org/admin).
1.2. Go to
Source Providers.
1.3. Select the Source Provider created
for this integration (e.g., "gundi_tahmo_UUID")
Please ensure your Route includes a destination, and review the Route Activity Logs for additional details. You should see some records mentioning that Gundi successfully delivered data to EarthRanger.
1.3. Click on Subject Details Configuration.
1.4. Configure the additional
information you would like to see on the map.
2. Configure these Subjects as a “Weather Station”.
3. Assign your Subjects to a Subject Group.
Please refer to EarthRanger's documentation or contact Support.
Data Pull Frequency
Approximately every 30 minutes.
Other Weather Station
| ZENTRA Cloud | Stevens Connect | Vital Weather |
| OpenWeather |
| Back to the integration catalog | Need help setting this up? Contact us |
